QNAP Utilities

QNAP RAM Benchmark

Peak read: the run's best read bandwidth, usually from a 1-second phase of the core-scaling sweep. JEDEC: the run's best stream, read or write, against the theoretical peak (channels × bus width × configured speed); blank where SMBIOS cannot give that peak. 60 s: mean read / write over the sustained phase, from MemHound 0.6.6 on. Compare within one memory type and channel count.

8 NAS unitsUpdated

Peak memory read bandwidth by NAS unit, highest first
# NAS model Memory Modules Peak read GB/s
 JEDEC Verdict Runs
1 TS-h1290FXAMDEPYC 7302P 16-Core DDR42933 MT/s 252 GB · 8×32 GB DDR4 3200 MT/sTS4GHR72V2E Peak read bandwidth
107.7
 old run* PASS 1 run
2 TBS-h574TXIntel12th Gen Core i5-1235U LPDDR44267 MT/s8-channel 15 GB · 8×2 GB LPDDR4 4267 MT/s Peak read bandwidth
40.4
60 s: 18.2 / 21.7 GB/s		 JEDEC 95% PASS 2 runs
3 TBS-h574TXIntel12th Gen Core i5-1235U LPDDR44267 MT/s8-channel 15 GB · 8×2 GB LPDDR4 4267 MT/s Peak read bandwidth
39.7
60 s: 18.9 / 22.3 GB/s		 JEDEC 95% PASS 2 runs
4 TS-673AAMDRyzen Embedded V1500B Quad-core2.20 GHz DDR42400 MT/s 63 GB · 2×32 GB DDR4 3200 MT/sCMSX64GX4M2A3200C22 Peak read bandwidth
31.3
 old run* PASS 3 runs
5 TVS-671IntelCore i7-4790S3.20 GHz DDR31600 MT/s 16 GB · 2×8 GB DDR3 1600 MT/s Peak read bandwidth
21.8
 old run* PASS 2 runs
6 TBS-464IntelCeleron N51052.00 GHz LPDDR42933 MT/s 8 GB · 2×4 GB LPDDR4 3200 MT/s Peak read bandwidth
15.2
 old run* PASS Fault reported: Samsung LPDDR4 4 GB 3200 MT/s (onboard), 8 Oct 2026, before the ranked run of 10 Oct 2026 1 run
7 TS-464IntelCeleron N51052.00 GHz DDR42667 MT/s 31 GB · 2×16 GB DDR4 2667 MT/sCT16G4SFRA266.M16FJ Peak read bandwidth
14.6
 old run* MARGINAL 1 run
8 TVS-473AMDEmbedded R-Series RX-421BD Radeon R7 DDR41866 MT/s 14 GB · 1×16 GB DDR4 2133 MT/s Peak read bandwidth
10.4
 old run* MARGINAL 2 runs

* From MemHound 0.6.3 or older (StorageDiag 1.6.10032 and older). Those builds counted one memory channel on AMD boards with two or eight, and read the Jasper Lake LPDDR4x bus as 64 bits, so this board showed 127 % to over 300 % JEDEC for three units. The stored rows lack the module locators and widths a recount needs, so the board leaves out their JEDEC figure and channel count. A new published run of Benchmark and Quality with StorageDiag 1.6.10033 or later replaces the row. Peak read is measured directly and stands.

1 faulty module reported, 0 confirmed by 3 or more units.